BellaVisage is easy to use. A treatment takes only a few minutes of your time. Be sure to follow our treatment plan to get the best results.

Treatment schedule
Treat each area separately for 10 to 15 minutes.
You can treat as many areas as you like in one session; it’s up to you.

Maintenance regime
To maintain your results, you should use BellaVisage for two sessions a week for 10 weeks.
After that, treat once every two weeks to maintain results.

Using the device
Follow the recommended order in the user guide and treat each zone for 10 to 15 minutes by holding the device against your skin. It is important that you treat each area individually, one small area of your face at a time. By doing this, the temperature on your skin remains constant. Don’t forget to include your neck and jawline in the treatment.

BellaVisage comes with a tube of Silk’n Slider Gel. This gel is required to carry out your treatments. It is important that you apply a thin layer of gel to your skin before you start treatment.

Without the gel, the device will not work. The water-based product not only moisturizes but also helps to guide the device. It ensures that BellaVisage moves easily over your skin and prevents it from overheating and reddening.

Wrinkle and skin treatment areas

• Forehead (including in between brows)
• Right Cheek (including around eyes)
• Left Cheek (including around the eyes)
• Right Lower Cheek (including nasolabial fold, or, laugh lines around the mouth, and jawline)
• Left Lower Cheek (including nasolabial fold and jawline)
• Neck – Treat here for smoothing

Treatment Steps

• Remove all jewelry.
• Press the start button to turn on the device. The level 1 energy level indicator light will go on.
• For your first treatment, start at energy level 1 for a few minutes, then set an energy level that is comfortable for the area you wish to treat. For future treatments, you can use an energy level that is comfortable for the area you wish to treat.
• Next, spread a thin layer of Slider Gel over the area. Always apply Slider Gel (or another clear, water-based gel) before you put the device on your skin.
• Press the treatment surface firmly against your skin. You will feel a mild sensation of warmth. Move the device in gentle, massage-like linear motions on the area you wish to treat. Progress slowly and carefully. Work each treatment area for 10 to 15 minutes. Make sure the treatment surface is in good contact with your skin.
• Immediately after the treatment, wash your face to remove any gel, then apply facial lotion or a mask.

You can expect to see visible results after multiple treatments and fuller results after completing full treatment regime.*

* Results may vary based on skin type and degree of laxity in skin.

Model no.: H2111, H2112
Treatment area: 468±5mm2
Technology: HT™
Red light (wavelength; optical output power): 630nm±20nm; 45±9mW/cm2
IR (wavelength; optical output power): 850nm±20nm; 57±11 mW/cm2
RF (frequency; maximum output power): 1 MHz ±30%; 10W max
Operation & Safety: Heat stabilizer preventing skin overheating
Package size: 22 cm X 22 cm X 9 cm
System weight: 125 gm
Transport & storage between uses and storage condition:

• Temperature: minus 40°-70°C
• Relative humidity : 10%-90%
• Atmospheric pressure: 500 – 1060 hPa

Operating Conditions

• Temperature: 10°-35°C
• Relative humidity: 30%-75%
• Atmospheric pressure: 700 – 1060hPa

Protection against electrical shock: Class II Medical equipment type BF applied part
Adapter models and rating

• KSA24A1200150HU
• Input: 100-240VAC, 50-60 Hz, 0.5A
• Output: 12V, 1.5A
• KSAPV0361200300D5
• Input: 100-240VAC, 50-60 Hz, 0.9A
• Output: 12V, 3.0A

The device was tested and complies with: IEC 60601-1 (Safety)

• IEC 60601-2-2 (High Frequency)
• IEC 60601-1-2 (EMC)
• IEC 60601-1-11 (Environment)
• IEC60601-2-57 (Safety of non-laser source)

Expected service life of the equipment: 5 years